Designed for the contractor, the CPS MK II feature 2-RU chassis, Phoenix-type connectors for inputs and outputs, pre-programmable power-on delay, easy power-on via remote contact closures, rear panel attenuators, and a switchable 50 Hz high-pass filter. Like the CPS multi. Two-Channel Models CPS, CPS, CPS, and CPS CPS2.x rear view. Remote power-on contact. 1. Programmable power-on timer. 2. Module slot for. Buy Electro-Voice CPS 2-Channel Power Amplifier for RCM IRIS-Net Remote Control Module (W, 4 Ohms) Review Electro-Voice CPS
|Published (Last):||16 October 2016|
|PDF File Size:||5.35 Mb|
|ePub File Size:||8.64 Mb|
|Price:||Free* [*Free Regsitration Required]|
To print the manual completely, please, download it.
Please update your browser to use Reverb
PARALLEL operation is the mode of choice, whenever the same input signal drives multiple cps.29 amp cpe2.9 of a large system installation. Make sure to completely read and fully observe power rating specifications of the speaker systems to be used and to check them against the output power capacity of the power amp.
Comments to this Manuals Your Name. This mode of operation is being used for all 2-channel applications, like stereo operation. Unbalanced connections should only be used if the cables are very short and no interfering signals are to be expected in the vicinity of the power amplifier. Please take time to consult this manual so that sv can understand all the features built into your Electro-Voice amplifier and fully utilize all its performance capabilities.
Please read and follow the instructions provided in the documentation that you have received together with each extension module. The audio signal has to be applied to the input connectors of channel 1, amplification is set via input level control of channel 1 only.
CPS MK II Contractor Precision Series Class‑H Power Amplifier by Electro‑Voice
The difference between power consumption and dispensed power is called power dissipation P d. Controls, Indicators and Connections Front View 1. In this case, bridging the screen shielding and the cps22.9 of the inverting input inside of the connector is mandatory. When installing the power amp in a case or rack system, attention should be paid to these details to provide sufficient ventilation. As with all Electro-Voice power amps with fan cooling, the airflow direction is front-to-rear, obviously because there is more cold air outside of the rack case than inside.
Due to their immunity against external interference sources, such as dimmers, mains connections, HF-control lines, etc. This indicates all protections are working fine. Keep ventilati- on louvers free from dust to xps2.9 unhindered airflow.
Don’t have an account? Turning the Mains Switch to ON starts booting up the power amp. Table of Contents Add to my manuals Add. The correct connection is also indicated at the amplifiers rear panel.
Speaker system switch-on is delayed by approximately 2 seconds via output relays, effectively suppressing any possible power-on noise, which otherwise might be heard through the loudspeakers.
Ventilation As fv all Electro-Voice power amps with fan cooling, the airflow direction is front-to-rear, obviously because there is more cold air outside of the rack case than inside. During installation, always separate the power amplifier from the mains. Level Indicators for channels 1 and 2 2.
Following table shows possible switch settings and corresponding delay times. Mounting CPS amplifiers have been designed for installation in a conventional inch rack case.
Do not use the power cpps2.9 near heat sources, like heater blowers, stoves or any other heat radiating devices. This mode of operation is being used for all 2-channel applications, like stereo operation. Amplification is set via input level control of channel 1 only.
Page of 24 Go. For pricing options and packages, contact us at Don’t show me this message again.
Inputs are electronically balanced. Additionally securing the amplifier at the rear becomes necessary, if the rack case in which the power amplifier has been installed will be transported.
Only the provided power cord may be used. Set the switch to the OFF position if no attenuation of low frequency audio signals is required. Enter text from picture: The connected speaker systems must be able to handle such voltages.